How to Square a Log with a Chainsaw

Cutting and squaring of logs is done for various purposes such as making firewood, for business purposes, or any other delegated household work.  For this to be successful, the right tool, which is a chainsaw, is needed.  Safety is always vital when using the chainsaw, thus the need to familiarize oneself with the basics, the techniques used, the dangers it poses, and the safety requirement to be put in place.

The article explains in details the required elements/equipment and the procedure of squaring or cutting a log using a chainsaw.

How to Square a Log with a Chainsaw

Important components/requirements for the task

  1. A chainsaw

This is the first element that enables the operation to take place. One is expected to select the right kind of chainsaw that is ideal for the intended task.

The chainsaw used is either gas or electric chainsaw depending on the size of the logs to be squared as well as the operation period.

  • Fuel

The chainsaw should have adequate oil to enable it to run throughout the operation without any troubles. Regardless of whether the chainsaw is using electricity or battery, one should use the right oil in the chain as it enables smooth cutting.  It is also recommended to have fresh oil for every session when cutting the logs.

  • Hammer

A hammer is essential in helping to drive the wedge in the logs for easier splitting and squaring as the first step of the process.

  • Claw bar

The claw bar is important when dealing with big logs. It aids in fast and smooth cutting. The claw bar helps in reaching a deep depth, especially in cases where the chain bar is too short, and the logs are big.

  • Splitting maul

It resembles an axe, although it is heavier and helps in pushing the sharp edges of the chainsaw into the logs for easier and fast cutting.

  • Safety gear

Safety gear is vital in case something goes south. It is critical to have the limbs protected as well as taking other safety measures even though the modern types of chainsaws are safer. The protective gear includes rubber boots, eye protector glass/safety goggle, gloves, ear defenders, protective trousers, and a hard hat.

All in all, having a clear knowledge of the log diameter is essential as it helps in determining the kind of engine and chain bar to use for the tasks.

The procedure

Squaring of the logs takes place in various positions. However, before the actual task, it is crucial to carry out the following:

  • Checking the chainsaw: It is essential to check if the chainsaw is ready for the set tasks. The fuel amount and condition, chain, saw belt among other components should be checked to ensure there won’t be any obstacles during the tasks.
  • Clearing the space: Plenty of space is vital during the process, and thus the area should be cleared, ensuring there are no objects, waste, or people within five meters of the log.
  • Getting the right posture: The posture is supposed to allow the upper body to support the chainsaw with ease. An upright position is recommended with the step wider than the shoulder-length for ultimate balance and safety.

The cutting techniques

Identifying the branches that cannot be used as logs is an ideal first step. The branches should be cut off as they can be an obstacle when squaring the logs. Once you get a suitable log after cutting the branches, the cutting positions follow.

Overcutting

It is also known as over bucking where the log is squared from the top having the log getting supported by the ground. Cutting from the top allows for the application of light pressure with the saw. This is the safest and simplest way to square a log. In case the chainsaw gets pinched, one is supposed to turn it off and use the hammer to drive the plastic or the wooden wedge into the cut and remove it.  Once done, it is easy to continue cutting the logs using the same method.

The log on a Hill method

 It is advisable to stand up-hill of the log when using this method. It is a safety precaution that ensures you are not hurt once the cutting is done and the logs rolls. It is essential to make sure there is no contact between the nose of the saw and the ground.

Support from both ends

This method allows the logs to be supported on the left and right side but not in the middle. It can be applied to both the bigger and smaller logs. The first cut should be from the top, around a third into the wood to avoid splintering then proceed to the underside where light pressure should be exerted.

One end support

This method ensures that one end of the log is in the air. The first cut should come from the underside towards the top of the log. The next cut should be made from the top to meet the first cut quickly without the chainsaw getting pinched. It is essential to observe the side which the cut log is to fall to avoid getting hurt.

Conclusion

Squaring of the small or large logs using a chainsaw is an easy task if the right procedure is followed. First, it is essential to ensure that the correct type of chainsaw is chosen depending on the number of logs. The right gear and components for the job should also be considered. The safety precaution should also be in place to ensure smooth operation without any obstacles.

Following the above-given procedure and techniques will play a significant role in handling the chainsaw and squaring of the logs efficiently.

Read more:

How to Cut A log Lengthwise Using A Chainsaw

How To Make a Straight Cut With a Chainsaw

How to cut logs into lumber with a chainsaw

Posted in guides | Leave a comment

How to Cut A log Lengthwise Using A Chainsaw

Either you are constructing a bench or building a fence post, there are ways you can cut a large log lengthwise using a chainsaw and in this guide, we will highlight the steps on how to achieve this. Although, you don’t need many tools to work with but can manage to cut through when you’re using the right chainsaw with several wedges to make firewood.

For a beginner this may be difficult to handle at first, hereby you are cutting the wrong way and making a mess of the logs available but with this guide and constant practice using the correct chainsaw; you will acquire relative experience and be able to cut as many logs as possible into the shape you want with no challenges.

However, working with the chain saw is very deadly; that is, the more you cut through woods, the more you go in search of more woods to cut and might sometimes cut yourself if the safety precautions are not adhered to strictly. However, you can wear protective clothing such as protective gear, and glasses before cutting any wood.

How to Cut A log Lengthwise Using A Chainsaw

What Do You Need?

To ensure a nice end product of your wood there are several methods you’ll need to consider and they are:

1.    You will need a strong chainsaw with long blades to cut through nicely.  However, when working on logs, slightly raise them off the ground as you want to avoid cutting through the soil.

2.    To avoid any messy shape, cut through vertically and avoid cutting through an angle.

3.    Use the tip of the straight shallow groove along the line you want to cut

4.    You need to get the relative amount of fuel that will be enough for you throughout the process and it’s better you purchase it before you start cutting with your chainsaw to avoid mechanical problems.

5.    Safety is very important in this work; therefore it is important to have the right safety gear which will prevent damage to any part of your body. However, with this safety gear, you also need to operate the machine safely and follow all the precautions such as:

•    Using ear muffs to protect the ear from loud noise from the chainsaw

•    Protective clothing such as gloves, overalls, boots, etc.

•    You can also have someone around to keep you company in case of emergencies.

Now we’re ready to cut through our log but strictly follow these steps:

Step One

Build a 4×4 wood post on the ground and make sure it is upright.  This will help control your chainsaw. Afterward, construct a stand that will clamp your chainsaw. To cut through your wood, place it close to the post and direct the chainsaw straight down through the markings. For safety, you can add support to the log to prevent it from tipping over.

Step Two

Put your bolt on the log dog in a certain way (it must be completely crust-free at this point, especially for beginners.) tick each end of your bolt with a plane that marks the scabbard and cross-section. Then use ink to mark the edge of the log that you will cut. From the angle of the projected hanging rope, thick lines or ink lines (broken chalk) make a bolt in the corner at the other end of the bolt. This is the line where you directly cut. Afterward, remove the screw by removing the circle plate from the screw.

Step Three

Be prepared to cut “hook cant”. Now you have to find out what you want from the hook installed because as it can only function properly with large wood. If you want any shape, you need to know what size you must (pay attention to “cutouts”). Don’t try to cut something thinner than 30mm, it’s just not feasible. After you make a choice of shape and size which you have marked on the board, till you cut out your desired plank

Step Four

Before the cutting begins you must have the biggest saw you can get with a minimum of approximately 1 meter that is the longer the chainsaw, the more effective it will be. You have to be able to keep this machine in front of you with your hand fully extended with the trunk and the chainsaw functioning, if you can’t, that means you are not strong enough to do this job safely or effectively.

However, if you are a climber or you perform different endurance workouts like me, you should be able to put one hand aside and complete this easily. This work requires strength, endurance, and good eye coordination.

Start the saw at the end of the cant hook which is between the kerf lines that you have previously broken. This should now extend the length of the wood and the edge of the hook that is hanging that you’re about to cut. However, some like to stand and cut towards marking on the log, while others start cutting to the end. (The latter may be more accurate, but it is far riskier).

Step Five

At this stage, you are now ready to mill several logs, but there is one very important moment that many, even some individuals with relative experience forget. Do not leave the logs with each other until they are cut, but put them at both ends with a little relish attached to wood, and then clean it.

How to Cut A log Lengthwise Using A Chainsaw 1

Finally, with the steps above, you can successfully cut through a log with a chainsaw; however, make sure you follow every instruction especially safety measures. So whether on a farm where there are a lot of trees, you can cut all the way and may wood into different shapes and store them up to be used.

Reference Source: https://permies.com/t/31962/Free-hand-milling-lumber-chainsaw

Related Posts:

How To Make a Straight Cut With a Chainsaw

How to cut logs into lumber with a chainsaw

Posted in guides | Leave a comment

How To Make a Straight Cut With a Chainsaw

Chаіnѕаwѕ offer brutе cutting роwеr, but thеу aren’t thе mоѕt ассurаtе tооl іn the ѕhор. Nеvеrthеlеѕѕ, you саn mаkе an lеvеl сut with уоur сhаіnѕаw using this ѕіmрlе tесhnіԛuе.

Stumрѕ, logs, аnd telephone роlеѕ саn bе used аѕ wоrk tables оr supports, but thеу rеԛuіrе an flаt surface—which is difficult to achieve using a сhаіnѕаw. You can buіld a bаѕіс ѕԛuаrе jіg uѕіng 2 x 4ѕ and an lеvеl, аnd thеn ѕlіdе іt оvеr thе lоg оr роlе уоu want tо сut. Uѕе a level tо mаkе ѕurе іt’ѕ flаt and ѕесurе іt іn place uѕіng deck screws.

Thе kеу tо making thіѕ work wіthоut the chainsaw dіggіng іntо thе jig аѕ уоu ѕlіdе іt асrоѕѕ іѕ tо attach two thіn wооd ѕtrірѕ to thе сhаіnѕаw bаr.

Ovеrbuсkіng оr Overcutting

Thіѕ rеfеrѕ tо a cut frоm the tор оf the lоg where the lоg is ѕuрроrtеd thе full lеngth bу thе grоund.

Thіѕ іѕ thе ѕіmрlеѕt and safest wау to сut an lоg. Stаrt thе cut аt thе tор of thе log аnd аррlу light рrеѕѕurе wіth thе ѕаw, but trу to lеt thе ѕаw do the wоrk аѕ the tееth ѕhоuld рull thе сhаіn bar into the log. Trу to make sure thе guіdе bar nоѕе dоеѕ nоt contact thе ground or any other оbjесtѕ. If the guіdе bar does get саught or ріnсhеd іn thе lоg, dо nоt try tо force іt оut.

Turn off thе chainsaw, аnd drіvе a plastic оr wооdеn wеdgе іntо the сut with a hаmmеr so that the ѕаw саn bе easily rеmоvеd. Do nоt try and rеѕtаrt уоur сhаіnѕаw whіlе it іѕ ріnсhеd іn an lоg. Rеѕtаrt the ѕаw аnd аttеmрt tо fіnіѕh the сut wіth the ѕаmе dоwnwаrdѕ mоtіоn.

Lоg ѕuрроrtеd both ends but nоt in thе mіddlе, thіѕ ѕіtuаtіоn could іnсludе small logs that are ѕuрроrtеd оn a sawhorse or bіggеr lоgѕ thаt аrе ѕіttіng оn twо other pieces оf tіmbеr оr whеn thе ground dips іn thе middle оf thе lоg.

Hоw tо cut lоg ѕuрроrtеd bоth ends

Fіrѕt сut thе lоg from thе top about 1/3 оf thе wау into thе wооd. Nеxt сut frоm thе underside (underbuck), еnѕurіng уоu аrе only exerting lіght рrеѕѕurе upwards, till уоu reach the first cut tо аvоіd thе lоg pinching thе chainsaw bаr.

Underbucking Nоtе: whеn реrfоrmіng аn undеrbuсk thе сhаіnѕаw will wаnt tо рuѕh back аt you. Make ѕurе уоu are rеаdу for thіѕ force аnd hold thе ѕаw firmly bеіng саrеful аѕ you dоn’t want tо tо рull thе ѕаw up tоо hard аnd hіt уоurѕеlf.

Log supported on one еnd, wіth the other іn the аіr.

Fіrѕt сut ѕhоuld сut ѕhоuld bе made from the undеrѕіdе towards the tор (undеrbuсk) аbоut 1/3 of the wау through the lоg. Nеxt оvеrbuсk frоm the tор tо mееt the fіrѕt сut, thіѕ wіll hеlр thе ѕаw gеttіng ріnсhеd. Juѕt rеmеmbеr tо be ready when the сut portion оf thе lоg fаllѕ, mаkе sure уоu аrе not in thе lіnе оf fаll.

Lоg іѕ оn a Hіll.

Thе gоldеn rule whеn сuttіng lоgѕ whеn уоu аrе оn a hіll оr аn angle іѕ tо ALWAYS ѕtаnd uр-hіll of the lоg. If whеn thе сut is fіnіѕhеd thе lоg rоlеѕ you wіll nоt gеt hіt аnd hurt bу іt. Alѕо rеmеmbеr nоt tо lеt the nоѕе оf thе saw соntасt the ground.

The strаіght frоm bеhіnd felling cut

For small trees, thе еаѕіеѕt wау tо ѕаw thе fеllіng сut іѕ ѕtrаіght frоm behind. Thіѕ саn bе dоnе wіth оr without the bumper ѕріkе, depending оn the trее tо bе felled.

Straight frоm behind

If уоu аrе inexperienced, ѕаw wіth a pulling сhаіn (bottom оf thе guіdе bаr). Thіѕ wау thе saw іѕ not pushed against уоu, mаkіng thе work a bіt еаѕіеr. Othеrwіѕе іt is ԛuісkеr to saw wіth a рuѕhіng сhаіn (top оf thе guіdе bаr) ѕіnсе you can ѕtау іn thе ѕаmе position аѕ уоu wеrе іn fоr the dіrесtіоnаl nоtсh.

It іѕ very importantly thаt the fеllіng сut is ѕаwn раrаllеl to thе dіrесtіоnаl nоtсh tо еnѕurе аn еԛuаl thickness along the lеngth оf thе hinge.

Fоr ѕmаll trees, іt іѕ dіffісult tо use a brеаkіng bаr or fеllіng wеdgе. If thе trее lеаnѕ a little, thе guіdе bаr wіll pinch. However, уоu саn nоrmаllу рuѕh thе trее forward uѕіng уоur hаnd аgаіnѕt thе trunk оr a роlе with spikes. With a 4-5 mеtrе lоng роlе wіth ѕріkеѕ, you can еvеn рuѕh fоrwаrd rаthеr tаіl-hеаvу trееѕ by hаnd.

Thіѕ mеthоd саn also bе uѕеd оn thісk trееѕ аѕ lоng as thе trее dоеѕ nоt lean bасkwаrd аnd іf there аrе nо adverse wіndѕ. If there іѕ an rіѕk thаt thе tree wіll fаll backward аnd is too heavy to bе pushed fоrwаrd, уоu ѕhоuld uѕе thе fеllіng tools. In this саѕе, ѕаw untіl уоu саn fit a wеdgе or brеаkіng bаr in the ѕаw сut. Whеn was уоu ѕtаrt tо rеасh thе fіnаl thісknеѕѕ оf thе hіngе, bе careful to ensure that the hіngе hаѕ a еvеn thісknеѕѕ.

Frоm bеhіnd fеllіng cut uѕіng bumреr ѕріkе

The bumper ѕріkе acts аѕ a pivot bеtwееn the engine body аnd guіdе bаr. Apply the bumper ѕріkе’ѕ lоwеr tip at the іntеndеd hіngе width. Prеѕѕ wіth уоur lеft hand аgаіnѕt the front hаndlе while lіftіng thе rеаr handle wіth уоur rіght hаnd. Saw wіth a рullіng сhаіn untіl уоu have асhіеvеd thе appropriate hinge wіdth (аnd unіfоrm thісknеѕѕ!). Remember tо іnѕеrt thе felling wеdgе into thе ѕаw сut after ѕаwіng half of thе diameter.

You can аlѕо ѕаw frоm thе орроѕіtе direction uѕіng a рuѕhіng chain аnd apply thе uрреr tір of the bumреr ѕріkе. However, ѕаwіng this wау uѕuаllу becomes mоrе іrrеgulаr аnd thеrе is grеаtеr еngіnе resistance.

Sаvеd еdgе method

Instead оf ѕаwіng through thе full trее dіаmеtеr whеn cutting frоm bеhіnd, wіth thіѕ mеthоd уоu ѕаvе аn еdgе оn thе орроѕіtе ѕіdе. Thіѕ рrеvеntѕ thе tree frоm fаllіng backward, аllоwіng a felling tооl tо bе uѕеd іn the felling сut.

Bоrе сuttіng

Tо bе able to perform thе ѕаfе соrnеr method аnd turn аrоund mеthоd уоu nееd tо master bore сuttіng. This іnvоlvеѕ mаkіng a сut іntо thе tree uѕіng thе tip оf the сhаіnѕаw’ѕ bаr. A bore саn bе uѕеd wіth mоѕt felling mеthоdѕ аnd саn bе аррlіеd rеgаrdlеѕѕ оf guіdе bаr lеngth аnd tree ѕіzе.

How tо mаkе a bоrе сut

At full throttle, аррlу thе bоttоm раrt оf thе guide bаr tip (рullіng сhаіn) slightly bеhіnd thе dеѕіrеd hinge width. When the guіdе bar tір hаѕ еntеrеd thе trunk, саrеfullу turn the guіdе bаr untіl іt is раrаllеl wіth the directional nоtсh. Nоw рuѕh thе guіdе bаr into thе trее as dеер аѕ nесеѕѕаrу. Adjust the hіngе wіdth аt thе еnd tо еnѕurе a unіfоrm thісknеѕѕ.

Safe соrnеr mеthоd

As thе name ѕuggеѕtѕ, a соrnеr оf thе tree trunk is lеft unѕаwn fоr оnе lаѕt сut before thе tree іѕ felled. A big advantage of thіѕ method іѕ that thе hinge can be сlеаrlу сut and іnѕресtеd before thе tree is felled. In аddіtіоn, thе saved соrnеr prevents thе trее frоm falling backward. Thіѕ method іѕ also well suited fоr moderately fоrwаrd or backward lеаnіng trees.

Turn around mеthоd

This method аlѕо uѕеѕ bоrе сuttіng. Fоr trees wіth a dіаmеtеr larger thаn the guіdе bаr lеngth.

Make a bоrе as dеер аѕ possible. Sаw to a ѕuіtаblе hinge thісknеѕѕ раrаllеl tо thе directional notch. Saw ѕtrаіght bасk, аррrоxіmаtеlу one guіdе bаr wіdth. Swіng thе ѕаw around the trunk but аvоіd ѕаwіng into thе hinge. Dо not fоrgеt tо plus tо іnѕеrt thе wеdgе оr breaking bаr. Continue to ѕwіng thе ѕаw, соmрlеtіng thе felling сut and сrеаtіng a hinge with a unіfоrm thісknеѕѕ аnd еvеn сut (vеrу іmроrtаnt!)

Posted in guides | Leave a comment

Top 5 American Made Chainsaw Brands

With so many different types and brands of chainsaws available on the market, it can easily become overwhelming when you are looking for good, American made one.  While it is often said that the absolute best brand of chainsaw for a specific job is going to be the one that is able to get the job done, it actually really comes down to the amount of power it has, how heavy it is, and how easily it can be used by the user, as well as safety features.  On top of that, it will need to be affordable to the potential buyer.

So you decided that you in need of a chainsaw, however, you have no idea on where to begin looking for one.  Some of the very first things that may pop into your mind are which brands of American chainsaws are the best?  Which brands of chainsaws are available to me?  Am I going to need to know anything before going out and buying one?

Before you can find which of the American chainsaw brands is going to be best for your individual needs, you must first know exactly why American chainsaws are better.

Why An American Made Chainsaw?

American chainsaws are very sought after, as all tools that are made in America are known for their extra high innovation and quality.  In fact, when you do buy a chainsaw that was made in America, you are not only purchasing a quality and dependable tool, but you are also supporting the American economy, as well as supporting American jobs.

Here is a list of all the chainsaw brands and models that are still being built in American factories.

Husqvarna

American Made Chainsaw Brand

One of the few chainsaws that are manufactured in America, Husqvarna chainsaws are tough, built to last, and have the power that you require to get the job done quickly.  With several different models to choose from, when you select Husqvarna, you know that you are getting quality.

Some of their chainsaw models include the 235 and 235e, the 240 and 240e, 435, 440 and 440e, 445, 450e, 455 and 455e, and the 460.

All of these chainsaw models produced by the brand Husqvarna are made in America.

Jonsered

Husqvarna chainsaw brand

Another one of the great American chainsaw brands, these chainsaws are perfect for just about any job you can think of.  While the Jonsered models of chainsaws are not going to necessarily be the cheapest chainsaw options available, they are going to be one of the best options available to you.  The Jonsered line of chainsaws was designed to do one thing, be the perfect chainsaw, and they are pretty close to that.

The Jonsered chainsaws that are made in America include the CS2166, the CS2234, the CS2238, CS2240, and the CS2255.

As with all of the chainsaws listed in this article, these too are an American made chainsaw brand.

Poulan Pro

Poulan Pro chainsaw brand

The Poulan Pro brand of chainsaws is perfect for any project no matter how big or small.  With enough power to cut through the biggest of tree stumps, they are also light enough for easy maneuverability, as well as easy transport.  Priced similarly to many of the other American made brands of chainsaws, when it comes to Poulan Pro chainsaws, you know exactly what you are getting, a high quality cutting machine.

The Poulan Pro chainsaws models include the PP3516AVX, PP3816A and PP3816AV, the PP4218A, PP4218AV and PP4218AVT, the PP4818A, and the PP5020AV.

Keep in mind that the different series of chainsaws will come with different features and safety; they will all be able to do the job.

Poulan

Poulan chainsaw brand

While technically it is not a different brand than the Poulan Pro, the Poulan series of chainsaws is a completely different set and can easily be considered a separate brand if you wanted to do that. 

Anyways, with that being said, here are the different models of Poulan brand chainsaws.  The Poulan chainsaws include the P3314 and P3314WSA, P3416, P3816, P4018 and P4018WT.

While these are not as serious as the Poulan Pro series, they are perfect for jobs around the house such as clearing brush, removing branches and limbs, and anything else that needs to be done.

McCulloch

McCulloch chainsaw brand

While the McCulloch brand of chainsaws does not necessarily have as many options to choose from, it is still one of the better made in America chainsaw brands.  Think of McCulloch chainsaws as ‘quality over quantity’, when it comes to their line of chainsaws.

The McCulloch series of chainsaws include the CS340, CS380, and the MC4218AV.

These are the top 5 American made chainsaw brands that are available on the market today.  Now keep in mind that while these chainsaws are all manufactured in America, the parts that are used to build them are from both foreign and domestic suppliers.  If you would like to learn more information about this, you can check with the manufacturer of the chainsaw.

One last thing, no matter what type of chainsaw that you are using, be sure that you are always practicing safe chainsaw techniques, and are wearing all of the required personal protective equipment.  This way you will be less likely to have any type of chainsaw accident.  Remember, safety first!

Posted in tools | Leave a comment

How to cut logs into lumber with a chainsaw

Most people who work in wood will understand the importance of lumber, without it, the trees would not be able to be turned into all of the wonderful things that we use wood for. Tables, chairs, benches. Before it can be made into any of them, it needs to first be made into wooden beams. And the best way to do this is by using a chainsaw.

What is lumber? Lumber is basically wood that’s been cut so that it can be used but is yet to be made into anything. It should be flat and smooth on all sides. So long as you create it properly working with it to create things will be easy! Just follow this simple guide, wear protection, and always be careful!

How to cut logs into lumber with a chainsaw

Step One: Lift the log

The first step is to make sure it’s elevated and secure, doing this will ensure that it doesn’t roll away when you’re working with it, but also it puts it at an appropriate height for you to work with.

The best way to get it to this height is to create a ramp which you can use to roll your log to a height which will be easy to work with. For safety, make sure that you add some support from underneath, just incase your supports give way.

Now that your log is lifted and secure, you will be able to work with it, you would have to worry about it rolling away, and you won’t have to damage your back by going down to the ground all the time.

Step Two: Flatten the top

The purpose of the first cut is going to be to make sure that the log has one flat side.

Firstly measure down about 11/2 inches away from the top of the butt and then do the same at the tip, for those who are unaware, the butt and tip are what the ends of the log are called.

If the size of the tip is vastly different to the butt, measure down about 2 or maybe 4 inches at the butt instead of 11/2..

With the measurements made, just go ahead and attach the metal plates, this can usually be done by either using screws and a screwdriver, or hammer and nails, whichever one works best for you.

In order to make this cut easier, it will help is you add some weight to the top of the log. You might think that this will mean going out and buying some expensive long weight, but the reality is that it can be done with something as simple as a ladder. Or anything that’s both long and heavy. If it will add pressure on top of the part you’re cutting off, it’s good enough.

This sort of cutting is going to be very difficult if you don’t use a cutting guide, this is a simple chainsaw attachment that you can buy from most woodwork shops. Once you’ve attached it to your chainsaw, cut from the bottom of one metal plate, all the way to the bottom of the other. This usually takes a bit of time, and because you’re using a chainsaw, please take the appropriate safety precautions.

You’ve now got your first flat side. So that’s one down, and two to go.

Step Three: Turn and repeat

You’ll now have to roll this log over, it doesn’t matter too much which way, so long as there is bark facing the sky. Just repeat the same process as you did the first time round, by attaching the metal plates (usually parallel to one another) and cutting from one plate to the other, using a cutting guide chainsaw attachment. You’ll have to repeat the process one last time by rolling it over again, attaching the plates, and cutting. It does take time, but with the right equipment, it’s easy to do.

Step Four: Remove the Bark lines

At this point, you’ll have a rather odd looking thing. At the bottom will be bark, but on the sides there will also be thin lines of bark. You need to get rid of them. To do this adjust your cutting guide so that it’s just below the thin bark on the top, and cut it off.

Step Five: Take the bark off the bottom

Afterwards, repeat the same process of the bark at the bottom of the log. Once everything has been cut off, remove the bark from the bottom of the log. Right now what you’ll have is essentially a square log, it might look like the type of thing a giant might use if he ever wanted to do some building work, so be careful of a giant hand coming out of the sky, and taking it away from you. Should this happen just use your chainsaw on this fingers to get him to leave you alone.

But all jokes aside, this thing has a name, it’s called the kant. And you will be using it to create all of the boards which can be used to make wooden items.

Step Six: Board the kant

To cut the boards, firstly measure down from the top how thick you want the boards to be. This will vary depending on the type of wood, and what you intend to use it for. Using your saw cutting guide, cut all the way along. And there you will have your first board! Put it on a pile, and get ready for the next one.

It’s wise to allow your saw to cool down after about 3 boards. Chainsaws can get very hot, and often don’t work very well if overheated, it’s also important for you to rest as tiredness can significantly increase the risk of injury, and chainsaw injuries can be lethal! So please be careful!

There we have it, you have now turned a log into a pile of lumber using a chainsaw, and a cutting guide. Doing this process is important for anyone who wants to work with wood, as without turning it into lumber, wood would not be much use to anyone. If you’re new to woodwork, it’s best to get someone with more experience to be there, just in case something goes wrong!

Posted in article | Leave a comment